Allow dma_map_sgtable() to pass errors from the map_sg() ops. This
will be required for returning appropriate error codes when mapping
P2PDMA memory.
Introduce __dma_map_sg_attrs() which will return the raw error code
from the map_sg operation (whether it be negative or zero). Then add a
dma_map_sg_attrs() wrapper to convert any negative errors to zero to
satisfy the existing calling convention.
dma_map_sgtable() defines three error codes that .map_sg implementations
are allowed to return: -EINVAL, -ENOMEM and -EIO. The latter of which
is a generic return for cases that are passing DMA_MAPPING_ERROR
through.
dma_map_sgtable() will convert a zero error return for old map_sg() ops
into a -EIO return and return any negative errors as reported.
This allows map_sg implementations to start returning multiple
negative error codes. Legacy map_sg implementations can continue
to return zero until they are all converted.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduce nhi_check_quirks() routine to handle any vendor specific quirks
to manage a hardware specific implementation.
On Intel hardware the USB4 controller supports clearing the interrupt
status register automatically right after it is being issued. For this
reason add a new quirk that does that on all Intel hardware.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There was an "unknown" firmware variant turning up in the wild
causing problems in the clock driver. Add this missing variant
and clarify that varian 11 and 15 are Samsung variants, as this
is now very well known from released products.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For historical reasons x_tables still register tables by default in the
initial namespace.
Only newly created net namespaces add the hook on demand.
This means that the init_net always pays hook cost, even if no filtering
rules are added (e.g. only used inside a single netns).
Note that the hooks are added even when 'iptables -L' is called.
This is because there is no way to tell 'iptables -A' and 'iptables -L'
apart at kernel level.
The only solution would be to register the table, but delay hook
registration until the first rule gets added (or policy gets changed).
That however means that counters are not hooked either, so 'iptables -L'
would always show 0-counters even when traffic is flowing which might be
unexpected.
This keeps table and hook registration consistent with what is already done
in non-init netns: first iptables(-save) invocation registers both table
and hooks.
This applies the same solution adopted for ebtables.
All tables register a template that contains the l3 family, the name
and a constructor function that is called when the initial table has to
be added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need the fixes in here as well, and resolves some merge issues with
the mhi codebase.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty/serial driver fixes for 5.14-rc5 to resolve a
number of reported problems.
They include:
- mips serial driver fixes
- 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- other tiny driver fixes
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYQ++cg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylzoQCcC2zlnRRex48ovvh/b4JtKgImP6IAn2wR2Ag+
tSpMfooJBaT5a9kcg+Vr
=U7hC
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 5.14-rc5 to resolve a
number of reported problems.
They include:
- mips serial driver fixes
- 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- other tiny driver fixes
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_pci: Avoid irq sharing for MSI(-X) interrupts.
serial: 8250_mtk: fix uart corruption issue when rx power off
tty: serial: fsl_lpuart: fix the wrong return value in lpuart32_get_mctrl
serial: 8250_pci: Enumerate Elkhart Lake UARTs via dedicated driver
serial: 8250: fix handle_irq locking
serial: tegra: Only print FIFO error message when an error occurs
MIPS: Malta: Do not byte-swap accesses to the CBUS UART
serial: 8250: Mask out floating 16/32-bit bus bits
serial: max310x: Unprepare and disable clock in error path
Here are some small USB driver fixes for 5.14-rc5. They resolve a
number of small reported issues, including:
- cdnsp driver fixes
- usb serial driver fixes and device id updates
- usb gadget hid fixes
- usb host driver fixes
- usb dwc3 driver fixes
- other usb gadget driver fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYQ+/ow8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymdLACeMlXNPA5S/YJd+vak0Oer1mjNQWkAoJAZKLEN
bvN1v5wYjPs0mIFJUwj0
=xb57
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes for 5.14-rc5. They resolve a
number of small reported issues, including:
- cdnsp driver fixes
- usb serial driver fixes and device id updates
- usb gadget hid fixes
- usb host driver fixes
- usb dwc3 driver fixes
- other usb gadget driver fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
usb: typec: tcpm: Keep other events when receiving FRS and Sourcing_vbus events
usb: dwc3: gadget: Avoid runtime resume if disabling pullup
usb: dwc3: gadget: Use list_replace_init() before traversing lists
USB: serial: ftdi_sio: add device ID for Auto-M3 OP-COM v2
USB: serial: pl2303: fix GT type detection
USB: serial: option: add Telit FD980 composition 0x1056
USB: serial: pl2303: fix HX type detection
USB: serial: ch341: fix character loss at high transfer rates
usb: cdnsp: Fix the IMAN_IE_SET and IMAN_IE_CLEAR macro
usb: cdnsp: Fixed issue with ZLP
usb: cdnsp: Fix incorrect supported maximum speed
usb: cdns3: Fixed incorrect gadget state
usb: gadget: f_hid: idle uses the highest byte for duration
Revert "thunderbolt: Hide authorized attribute if router does not support PCIe tunnels"
usb: otg-fsm: Fix hrtimer list corruption
usb: host: ohci-at91: suspend/resume ports after/before OHCI accesses
usb: musb: Fix suspend and resume issues for PHYs on I2C and SPI
usb: gadget: f_hid: added GET_IDLE and SET_IDLE handlers
usb: gadget: f_hid: fixed NULL pointer dereference
usb: gadget: remove leaked entry from udc driver list
...
DO_ONCE
DEFINE_STATIC_KEY_TRUE(___once_key);
__do_once_done
once_disable_jump(once_key);
INIT_WORK(&w->work, once_deferred);
struct once_work *w;
w->key = key;
schedule_work(&w->work); module unload
//*the key is
destroy*
process_one_work
once_deferred
BUG_ON(!static_key_enabled(work->key));
static_key_count((struct static_key *)x) //*access key, crash*
When module uses DO_ONCE mechanism, it could crash due to the above
concurrency problem, we could reproduce it with link[1].
Fix it by add/put module refcount in the once work process.
[1] https://lore.kernel.org/netdev/eaa6c371-465e-57eb-6be9-f4b16b9d7cbf@huawei.com/
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Reported-by: Minmin chen <chenmingmin@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit marks some interrupt-induced read-side data races in
__srcu_read_lock(), __srcu_read_unlock(), and srcu_torture_stats_print().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
We have two separate sections that talk about why list_empty_rcu()
is not needed, so this commit consolidates them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
[ paulmck: The usual wordsmithing. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
KCSAN flags accesses to ->rcu_read_lock_nesting as data races, but
in the past, the overhead of marked accesses was excessive. However,
that was long ago, and much has changed since then, both in terms of
hardware and of compilers. Here is data taken on an eight-core laptop
using Intel(R) Core(TM) i9-10885H CPU @ 2.40GHz with a kernel built
using gcc version 9.3.0, with all data in nanoseconds.
Unmarked accesses (status quo), measured by three refscale runs:
Minimum reader duration: 3.286 2.851 3.395
Median reader duration: 3.698 3.531 3.4695
Maximum reader duration: 4.481 5.215 5.157
Marked accesses, also measured by three refscale runs:
Minimum reader duration: 3.501 3.677 3.580
Median reader duration: 4.053 3.723 3.895
Maximum reader duration: 7.307 4.999 5.511
This focused microbenhmark shows only sub-nanosecond differences which
are unlikely to be visible at the system level. This commit therefore
marks data-racing accesses to ->rcu_read_lock_nesting.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Commit b8c17e6664 ("rcu: Maintain special bits at bottom of ->dynticks
counter") reserved a bit at the bottom of the ->dynticks counter to defer
flushing of TLBs, but this facility never has been used. This commit
therefore removes this capability along with the rcu_eqs_special_set()
function used to trigger it.
Link: https://lore.kernel.org/linux-doc/CALCETrWNPOOdTrFabTDd=H7+wc6xJ9rJceg6OL1S0rTV5pfSsA@mail.gmail.com/
Suggested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: "Joel Fernandes (Google)" <joel@joelfernandes.org>
[ paulmck: Forward-port to v5.13-rc1. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Lots of small fixes for Arm SoCs this time, nothing
too worrying:
- omap/beaglebone boot regression fix in gpt12 timer
- revert for i.mx8 soc driver breaking as a platform_driver
- kexec/kdump fixes for op-tee
- various fixes for incorrect DT settings on imx, mvebu, omap,
stm32, and tegra causing problems.
- device tree fixes for static checks in nomadik, versatile, stm32
- code fixes for issues found in build testing and with static
checking on tegra, ixp4xx, imx, omap
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=h0YB
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-5.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Lots of small fixes for Arm SoCs this time, nothing too worrying:
- omap/beaglebone boot regression fix in gpt12 timer
- revert for i.mx8 soc driver breaking as a platform_driver
- kexec/kdump fixes for op-tee
- various fixes for incorrect DT settings on imx, mvebu, omap, stm32,
and tegra causing problems.
- device tree fixes for static checks in nomadik, versatile, stm32
- code fixes for issues found in build testing and with static
checking on tegra, ixp4xx, imx, omap"
* tag 'soc-fixes-5.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
soc: ixp4xx/qmgr: fix invalid __iomem access
soc: ixp4xx: fix printing resources
ARM: ixp4xx: goramo_mlr depends on old PCI driver
ARM: ixp4xx: fix compile-testing soc drivers
soc/tegra: Make regulator couplers depend on CONFIG_REGULATOR
ARM: dts: nomadik: Fix up interrupt controller node names
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
omap5-board-common: remove not physically existing vdds_1v8_main fixed-regulator
ARM: dts: am437x-l4: fix typo in can@0 node
ARM: dts: am43x-epos-evm: Reduce i2c0 bus speed for tps65218
bus: ti-sysc: AM3: RNG is GP only
ARM: omap2+: hwmod: fix potential NULL pointer access
arm64: dts: armada-3720-turris-mox: remove mrvl,i2c-fast-mode
arm64: dts: armada-3720-turris-mox: fixed indices for the SDHC controllers
ARM: dts: imx: Swap M53Menlo pinctrl_power_button/pinctrl_power_out pins
ARM: imx: fix missing 3rd argument in macro imx_mmdc_perf_init
ARM: dts: colibri-imx6ull: limit SDIO clock to 25MHz
arm64: dts: ls1028: sl28: fix networking for variant 2
...
We need to move to per-cpu state for both deferred inode
inactivation and CIL tracking, but to do that we
need to handle CPUs being removed from the system by the hot-plug
code. Introduce generic XFS infrastructure to handle CPU hotplug
events that is set up at module init time and torn down at module
exit time.
Initially, we only need CPU dead notifications, so we only set
up a callback for these notifications. The infrastructure can be
updated in future for other CPU hotplug state machine notifications
easily if ever needed.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
[djwong: rearrange some macros, fix function prototypes]
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Restrict range element expansion in ipset to avoid soft lockup,
from Jozsef Kadlecsik.
2) Memleak in error path for nf_conntrack_bridge for IPv4 packets,
from Yajun Deng.
3) Simplify conntrack garbage collection strategy to avoid frequent
wake-ups, from Florian Westphal.
4) Fix NFNLA_HOOK_FUNCTION_NAME string, do not include module name.
5) Missing chain family netlink attribute in chain description
in nfnetlink_hook.
6) Incorrect sequence number on nfnetlink_hook dumps.
7) Use netlink request family in reply message for consistency.
8) Remove offload_pickup sysctl, use conntrack for established state
instead, from Florian Westphal.
9) Translate NFPROTO_INET/ingress to NFPROTO_NETDEV/ingress, since
NFPROTO_INET is not exposed through nfnetlink_hook.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nfnetlink_hook: translate inet ingress to netdev
netfilter: conntrack: remove offload_pickup sysctl again
netfilter: nfnetlink_hook: Use same family as request message
netfilter: nfnetlink_hook: use the sequence number of the request message
netfilter: nfnetlink_hook: missing chain family
netfilter: nfnetlink_hook: strip off module name from hookfn
netfilter: conntrack: collect all entries in one cycle
netfilter: nf_conntrack_bridge: Fix memory leak when error
netfilter: ipset: Limit the maximal range of consecutive elements to add/delete
====================
Link: https://lore.kernel.org/r/20210806151149.6356-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
u32 is a type that is used for properties retrieval from DT.
With the type change it allows to clean up properties reading routine.
While at it, order the fields in way how they are parsed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20210802184355.49879-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Energy Model (EM) provides useful information about device power in
each performance state to other subsystems like: Energy Aware Scheduler
(EAS). The energy calculation in EAS does arithmetic operation based on
the EM em_cpu_energy(). Current implementation of that function uses
em_perf_state::cost as a pre-computed cost coefficient equal to:
cost = power * max_frequency / frequency.
The 'power' is expressed in milli-Watts (or in abstract scale).
There are corner cases when the EAS energy calculation for two Performance
Domains (PDs) return the same value. The EAS compares these values to
choose smaller one. It might happen that this values are equal due to
rounding error. In such scenario, we need better resolution, e.g. 1000
times better. To provide this possibility increase the resolution in the
em_perf_state::cost for 64-bit architectures. The cost of increasing
resolution on 32-bit is pretty high (64-bit division) and is not justified
since there are no new 32bit big.LITTLE EAS systems expected which would
benefit from this higher resolution.
This patch allows to avoid the rounding to milli-Watt errors, which might
occur in EAS energy estimation for each PD. The rounding error is common
for small tasks which have small utilization value.
There are two places in the code where it makes a difference:
1. In the find_energy_efficient_cpu() where we are searching for
best_delta. We might suffer there when two PDs return the same result,
like in the example below.
Scenario:
Low utilized system e.g. ~200 sum_util for PD0 and ~220 for PD1. There
are quite a few small tasks ~10-15 util. These tasks would suffer for
the rounding error. These utilization values are typical when running games
on Android. One of our partners has reported 5..10mA less battery drain
when running with increased resolution.
Some details:
We have two PDs: PD0 (big) and PD1 (little)
Let's compare w/o patch set ('old') and w/ patch set ('new')
We are comparing energy w/ task and w/o task placed in the PDs
a) 'old' w/o patch set, PD0
task_util = 13
cost = 480
sum_util_w/o_task = 215
sum_util_w_task = 228
scale_cpu = 1024
energy_w/o_task = 480 * 215 / 1024 = 100.78 => 100
energy_w_task = 480 * 228 / 1024 = 106.87 => 106
energy_diff = 106 - 100 = 6
(this is equal to 'old' PD1's energy_diff in 'c)')
b) 'new' w/ patch set, PD0
task_util = 13
cost = 480 * 1000 = 480000
sum_util_w/o_task = 215
sum_util_w_task = 228
energy_w/o_task = 480000 * 215 / 1024 = 100781
energy_w_task = 480000 * 228 / 1024 = 106875
energy_diff = 106875 - 100781 = 6094
(this is not equal to 'new' PD1's energy_diff in 'd)')
c) 'old' w/o patch set, PD1
task_util = 13
cost = 160
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160 * 283 / 355 = 127.55 => 127
energy_w_task = 160 * 296 / 355 = 133.41 => 133
energy_diff = 133 - 127 = 6
(this is equal to 'old' PD0's energy_diff in 'a)')
d) 'new' w/ patch set, PD1
task_util = 13
cost = 160 * 1000 = 160000
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160000 * 283 / 355 = 127549
energy_w_task = 160000 * 296 / 355 = 133408
energy_diff = 133408 - 127549 = 5859
(this is not equal to 'new' PD0's energy_diff in 'b)')
2. Difference in the 6% energy margin filter at the end of
find_energy_efficient_cpu(). With this patch the margin comparison also
has better resolution, so it's possible to have better task placement
thanks to that.
Fixes: 27871f7a8a ("PM: Introduce an Energy Model management framework")
Reported-by: CCJ Yeh <CCj.Yeh@mediatek.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The memslot for a given gfn is looked up multiple times during page
fault handling. Avoid binary searching for it multiple times by caching
the most recently used slot. There is an existing VM-wide last_used_slot
but that does not work well for cases where vCPUs are accessing memory
in different slots (see performance data below).
Another benefit of caching the most recently use slot (versus looking
up the slot once and passing around a pointer) is speeding up memslot
lookups *across* faults and during spte prefetching.
To measure the performance of this change I ran dirty_log_perf_test with
64 vCPUs and 64 memslots and measured "Populate memory time" and
"Iteration 2 dirty memory time". Tests were ran with eptad=N to force
dirty logging to use fast_page_fault so its performance could be
measured.
Config | Metric | Before | After
---------- | ----------------------------- | ------ | ------
tdp_mmu=Y | Populate memory time | 6.76s | 5.47s
tdp_mmu=Y | Iteration 2 dirty memory time | 2.83s | 0.31s
tdp_mmu=N | Populate memory time | 20.4s | 18.7s
tdp_mmu=N | Iteration 2 dirty memory time | 2.65s | 0.30s
The "Iteration 2 dirty memory time" results are especially compelling
because they are equivalent to running the same test with a single
memslot. In other words, fast_page_fault performance no longer scales
with the number of memslots.
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20210804222844.1419481-4-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make search_memslots unconditionally search all memslots and move the
last_used_slot logic up one level to __gfn_to_memslot. This is in
preparation for introducing a per-vCPU last_used_slot.
As part of this change convert existing callers of search_memslots to
__gfn_to_memslot to avoid making any functional changes.
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20210804222844.1419481-3-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
lru_slot is used to keep track of the index of the most-recently used
memslot. The correct acronym would be "mru" but that is not a common
acronym. So call it last_used_slot which is a bit more obvious.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20210804222844.1419481-2-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tag for toerh trees/branches to pull from in order to have a stable base
to build off of for the "Allow deferred execution of
iomem_get_mapping()" set of sysfs changes
Link: https://lore.kernel.org/r/20210729233235.1508920-1-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYQ0XAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymPsQCeLzeQco/wi96/nf2fhKqpAPsBtH4AoLqE8R7F
PDJCjDCLsbwL+7ZC2udo
=Fbxh
-----END PGP SIGNATURE-----
Merge tag 'sysfs_defferred_iomem_get_mapping-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core driver-core-next
sysfs: Allow deferred execution of iomem_get_mapping()
Tag for toerh trees/branches to pull from in order to have a stable base
to build off of for the "Allow deferred execution of
iomem_get_mapping()" set of sysfs changes
Link: https://lore.kernel.org/r/20210729233235.1508920-1-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'sysfs_defferred_iomem_get_mapping-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
The definition of CLK_MULTIPLIER_ROUND_CLOSEST is not aligned to the two
bit definitions next to it. A deeper inspection reveals that the
alignment of CLK_MULTIPLIER_ROUND_CLOSEST does match the most common
alignment.
Align the bit definitions for the various provider types throughout the
file at 40 columns, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5468cd9e50cda8fc59cb6baab9413c6c0de1a974.1626257689.git.geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This callback will allow to notify representors about relevant events
when in OFFLOADS mode. In downstream patches, this will be used to notify
about PAIR/UNPAIR devcom events.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In shared FDB there is only one eswitch which is active and it receives
traffic from all representors and all vports in the HCA.
While the Ethernet representor will always reside on its native PF
the IB representor will not. Extend send to vport rule creation to
support such flows. Need to account for source vport that sends the
traffic (on which the representors resides) and the target eswitch
the traffic which reach.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As shared FDB requires changes in two subsystems first expose the needed
core functions so the RDMA side can be changed.
mlx5_lag_is_master(): return true if a given mlx5 device is the lag master.
mlx5_lag_is_shared_fdb(): Returns true if the lag mode is shared FDB.
mlx5_lag_get_peer_mdev(): Return the peer mdev in lag.
The mentioned functions will be used by downstream patches in order
to add support for shared FDB for the RDMA side.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Export a function so users can retrieve the mellanox device that manages
the eswitch from the eswitch device.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Several gpiolib functions receive pointer to struct device_node which is
later passed to OF functions. These OF functions accept already pointer
to const, so gpiolib can follow similar approach to indicate they are
not modifying the struct device_node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Unify the declaration of of_count_phandle_with_args() between enabled
and disabled OF by making constifying pointed device_node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
elevator_get_default() uses the following algorithm to select an I/O
scheduler from inside add_disk():
- In case of a single hardware queue or if sharing hardware queues across
multiple request queues (BLK_MQ_F_TAG_HCTX_SHARED), use mq-deadline.
- Otherwise, use 'none'.
This is a good choice for most but not for all block drivers. Make it
possible to override the selection of mq-deadline with a new flag,
namely BLK_MQ_F_NO_SCHED_BY_DEFAULT.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Martijn Coenen <maco@android.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20210805174200.3250718-2-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch modified set_cs_timing parameter, no need pass in spi_delay
to set_cs_timing callback.
By the way, we modified the mediatek and tegra114 spi driver to fix build err.
In mediatek spi driver, We have support set absolute time not clk_count,
and call this function in prepare_message not user's API.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210804133746.6742-1-Mason.Zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As we know, spi core layer has removed spi_set_cs_timing() API.
So this patch moved spi_delay for cs_timing from spi_controller
to spi_device, because cs timing should be set by spi_device but
not controller.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210804133716.32040-1-Mason.Zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two users of iomem_get_mapping(), the struct file and struct
bin_attribute. The former has a member called "f_mapping" and the
latter has a member called "mapping", and both are poniters to struct
address_space.
Rename struct bin_attribute member to "f_mapping" to keep both meaning
and the usage consistent with other users of iomem_get_mapping().
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20210729233235.1508920-3-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defer invocation of the iomem_get_mapping() to the sysfs open callback
so that it can be executed as needed when the binary sysfs object has
been accessed.
To do that, convert the "mapping" member of the struct bin_attribute
from a pointer to the struct address_space into a function pointer with
a signature that requires the same return type, and then updates the
sysfs_kf_bin_open() to invoke provided function should the function
pointer be valid.
Also, convert every invocation of iomem_get_mapping() into a function
pointer assignment, therefore allowing for the iomem_get_mapping()
invocation to be deferred to when the sysfs open callback runs.
Thus, this change removes the need for the fs_initcalls to complete
before any other sub-system that uses the iomem_get_mapping() would be
able to invoke it safely without leading to a failure and an Oops
related to an invalid iomem_get_mapping() access.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20210729233235.1508920-2-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only actual use is to check in zorro_device_probe() that the device
isn't already bound. The driver core already ensures this however so the
check can go away which allows to drop the then assigned-only member
from struct zorro_dev.
If the value was indeed needed somewhere it can always be calculated by
to_zorro_driver(z->dev.driver)
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210730191035.1455248-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the case if dev is NULL in dev_{put, hold}, so the caller doesn't
need to care whether dev is NULL or not.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make controller driver specify the MMIO register region length
for range checking of BHI or BHIe space. This can help validate
that offsets are in acceptable memory region or not and avoid any
boot-up issues due to BHI or BHIe memory accesses.
Link: https://lore.kernel.org/r/1620330705-40192-4-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the MHI controller driver defines which channels should
have their inbound buffers allocated and queued. But ideally, this is
something that should be decided by the MHI device driver instead,
which actually deals with that buffers.
Add a flag parameter to mhi_prepare_for_transfer allowing to specify
if buffers have to be allocated and queued by the MHI stack.
Keep auto_queue flag for now, but should be removed at some point.
Link: https://lore.kernel.org/r/1624566520-20406-1-git-send-email-loic.poulain@linaro.org
Tested-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FPGA Manager
- Colin's change is a simple spelling cleanup.
DFL
- Martin's fist change exposes DFL feature revision to client drivers
- Martin's second change modifies a SPI driver to populate different
spi_board_info modaliases based on the DFL feature revision
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of my for-next branch) without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSdhnt2PwibB65UG0C3mJX/Vsn7uQUCYQqyeQAKCRC3mJX/Vsn7
uQBCAP9JAcGZf6Rd1uV6Y9P0jpAvnsRA5AnwpXT5Vmo3qAtGqwD8DK+19sdN5gIk
vUdicT7mH8ZO6OSIDxNg3/kXHgG69Ac=
=qlgw
-----END PGP SIGNATURE-----
Merge tag 'fpga-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-next
Moritz writes:
FPGA Manager changes for 5.15-rc1
FPGA Manager
- Colin's change is a simple spelling cleanup.
DFL
- Martin's fist change exposes DFL feature revision to client drivers
- Martin's second change modifies a SPI driver to populate different
spi_board_info modaliases based on the DFL feature revision
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of my for-next branch) without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
spi: spi-altera-dfl: support n5010 feature revision
fpga: dfl: expose feature revision from struct dfl_device
fpga: Fix spelling mistake "eXchnage" -> "exchange" in Kconfig
Replace IP_SFLSIZE() with struct_size() helper in order to avoid any
potential type mistakes or integer overflows that, in the worst
scenario, could lead to heap overflows.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPI DMA is one of the DMA modes supported on geni, this adds support to
enable that mode
Also do better documentation of the enum geni_se_xfer_mode.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210625052213.32260-3-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
GENI_IF_DISABLE_RO is used by geni spi driver as well to check the
status if GENI, so move this to common header qcom-geni-se.h
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210625052213.32260-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
taregeted for v5.15:
- Add DT bindings to the expansion bus and PATA libata driver.
- Add a new expansion bus driver.
- Rewrite the watchdog driver to use the watchdog core and
spawn from the timer (clocksource) driver.
- Refactor the PATA/libata driver to probe from the device
tree and use the expansion bus driver to manipulate chip
select timings directly.
-----BEGIN PGP SIGNATURE-----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=v2E7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmEKnj0ACgkQmmx57+YA
GNn+UBAAiZI7jAfykKZ/r0IHlspI88deTvfiDtBsMmPHtRfW67yFsRzKmU/TL21y
ae7tPVOMgfPJ+AXLbARh0KnpmIXm++A7lY2PJezth38Gxm5Gx8rGbX41V6w6ZFH4
Zn+lJR6pv+wccqz7QqEWPhKrbvYybCdwYpFjkZUUjyxMjjiWCXvl+M3PaIKtVITj
a7t+hLFJ/h6IbBX3igZZG/fXfQh30HSrmaEzA08Uuamn3EUfYof+xfLAZ0xwhmnh
v9E5b27yRRhxir6nUFPlqt9+meAqFsK6eqrb5aZpjloBUJas8mkcOnF8Ch0d/0jn
TJJMImxU3eoeWi/8LHFSUl65Xxo8hTAwtpC5fMseDh0n0p5aFL5D6gbKeJ89PgeO
HRUc1YG05IgtF+70TyldxtLMdZwyBIwFMTIBaJPbT/Zz21LjZbep6sEIZkKGuE8I
n5p1tGX2Hjxqfcfk6Ftl+NY4V80BX+kq0esU0RT0Bve0swed22GIq0tH/8680ln8
G61pDuQqVEedxq8WrxfXdptb5iBOkiNI7HgBmvkpw0U986BwGtqFrYBKeFYj/wOQ
LGcqWSGaFcofDIySKrTsR8im51CHwKou+hrFusItFlcCjC4DPcMVo0+1BdYfp0Zo
vQ09IaHb209uw62YjBQe4MaAQxmm21zzLEqk6LUNd4hyEpOdx2w=
=2bLl
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-drivers-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/drivers
IXP4xx driver updates for modernizing the IXP4xx platforms,
taregeted for v5.15:
- Add DT bindings to the expansion bus and PATA libata driver.
- Add a new expansion bus driver.
- Rewrite the watchdog driver to use the watchdog core and
spawn from the timer (clocksource) driver.
- Refactor the PATA/libata driver to probe from the device
tree and use the expansion bus driver to manipulate chip
select timings directly.
* tag 'ixp4xx-drivers-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
pata: ixp4xx: Rewrite to use device tree
pata: ixp4xx: Add DT bindings
pata: ixp4xx: Refer to cmd and ctl rather than csN
pata: ixp4xx: Use IS_ENABLED() to determine endianness
pata: ixp4xx: Use local dev variable
watchdog: ixp4xx: Rewrite driver to use core
bus: ixp4xx: Add a driver for IXP4xx expansion bus
bus: ixp4xx: Add DT bindings for the IXP4xx expansion bus
Link: https://lore.kernel.org/r/CACRpkdZaCosXsgp02nuUbd_nEvdxm5-z0+d0oSA97UTWQ0RQQg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
